 |
|
|
|
| BRM PORSCHE 962 / IMSA /
TOYOTA 88C |
 |
Any BRM 1/24 Scale Porsche 962/IMSA/Toyota 88C ( If available at the time ) Kit cars only, White Kits must be Painted.
CAR CHOICES
BRM 001 Porsche 962C - Kenwood White #10
BRM 002 Porsche 962C - Kenwood Black & Red #10
BRM 003 Porsche 962C - FromA #27
BRM 004 Porsche 962C - Leyton House #16
BRM 005 Porsche 962C - Momo #30
BRM 006 Porsche 962C - Advan #25
BRM 007 IMSA Porsche Bud #86
BRM 008 IMSA Porsche Coke #5
BRM 009 IMSA Porsche Lowenbrau #14
BRM 010 IMSA Porsche Miller #14
|
 |
CAR SETUP RULES & REGULATIONS
All cars must be built Box Stock using only parts that came in the kit, or stock BRM replacement parts.
Parts must be fitted in the STOCK position, extra shims or spacers allowed.
Following exception are allowed:
- KD124080BRM or Original S-021 BRM Rear Tyres only.
- Front tyres are to be Stock BRM tyres only.
- Wheels and Tyres must not be visible outside the body when viewed from above.
- You can not paint front tyres to reduce grip.
- All races will be run using BRM Tyres Or , KD124080BRM only, no chemicals on tyres for cleaning etc. (CRC WD40 )
- Rear tyres may be lightly sanded to clean up.
- Gearing will be 8 Pinion and 36 Crown only
- No magnets allowed
- Front mirrors my be removed before racing.
- Chassis can have De burring or Sanding for Oscillation.
- May glue or stick washers, Foam onto the Body mounting screws to ease fitment.
- It is advised to cover screws with tape to prevent loss during the race.
- Chassis ( Old to New ) - The only difference is the cut outs to allow quick removal of the wheels and for resetting the gear on the Rear axle. It is permissible in the rules to modify the early chassis BRM 001 thru to 010 to replicate the later one. As long as no more plastic is removed than in the later versions.
- Trimming of the front edge of the Chassis to allow braid clearance is allowed.
- De burring or removing of flashing is allowed.
Car can not be raced without the Rear Wing, if it comes off you must replace it before continuing on
in the race (under Green, which means during the race not at the end of that Heat). Any minor parts that are lost during
the race must be refitted before the next race starts. (Wheel inserts, Headlight buckets, etc)
May use oil or grease to lubricate motor, gears and axles. You may lightly sand tyres - no other chemicals or additives allowed.
The motor must remain STOCK and can not be modified in any way, you can glue in the motor. Motors may not be opened or tampered
with any markings on the motor will be presumed as signs of an opened motor and the car will be disqualified. Motor lead wires may
be modified or shortened in any way you choose.
You may glue in axle bearings or glue on any part supplied with the kit.
The intent with the BRM Races is to run the cars as "STOCK" as possible! any breach of the RULES will mean exclusion from
the race.
All protests must be filed before the Race starts unless concerning modification of a car during the race.
TECH TIPS - GEARS
The biggest area to pay attention to are setting up the gear mesh. It is best to set these cars up with zero lash at the tightest
spot on the crown gear, and no side float in the rear axle. Any side float will allow the mesh to change as the car switches from
left to right in the turns changing mesh or lash and quickly destroying gears.
Once worn in this is less of an issue, but it is very different to the 1/32 scale cars with self aligning gears.
Page Top
|
|
|
 |
|
